Ubiquiti NanoStation M LocoM2 2.4GHz 8.5dBi
€45.96
Tax excluded
The Ubiquiti NanoStation M LocoM2 2.4GHz 8.5dBi is a product of the Switches and Access Points section - New status access points.
NanoStation Loco M2 is a very compact outdoor equipment, which integrates 2 antennas (MIMO) of 8 dBi gain for the 2.4 GHz band. The actual transfer speed of the equipment is up to 150 Mbps.
Another great advantage is the high transfer speed of the 802.11n standard, thanks to the TDMA Time Division Multiplexing technology, it allows more than 300 clients to be connected to the equipment.
This model has a low latency. Compared to the Nanostation M predecessors, the Nano Loco M2 has a processor with a higher clock frequency of 400 MHz and more memory.
Another great advantage is the high transfer speed of the 802.11n standard, thanks to the TDMA Time Division Multiplexing technology, it allows more than 300 clients to be connected to the equipment.
This model has a low latency. Compared to the Nanostation M predecessors, the Nano Loco M2 has a processor with a higher clock frequency of 400 MHz and more memory.
Simple and transparent administration website.
Some examples of possible configurations can be: AP, client or WDS mode. Traffic Shaping. QoS Transparent bridge or routing between WAN and LAN, with NAT or without NAT. Specific LED to indicate the strength of the signal. Output power 23 dBm.
The equipment supports IPv6 in bridge mode and WDS.
Includes the 24V PoE injector needed for power, the injector has a reset button, you can use this button to change the device to the recovery mode and upload the firmware via TFTP.
Another advantage is that it supports PoE on the secondary ethernet port, which allows it to power another device. This feature can be disabled through software.
Important information about compatibility:
This device uses the new AirOS V firmware version. For this reason, the device may not be fully compatible with other radio devices.
The AirOS system is continuously improving, so it is recommended to always update the firmware to the latest version.
| Brand | Ubiquiti |
| Model | NanoStation Loco M2 |
| characteristics | - Processor: Atheros MIPS 24KC, 400MHz |
| Additional characteristics | - Dimensions: 163x31x80 mm - Weight: 0.18 kg - Regulation: FCC Part 15.247, CE, IC RS210, RoHS - RX sensitivity: min. -83dBm +/- 2dB at 11b / g, min. -96dBm +/- 2dB in 11n - Maximum power consumption: 5.5 W - Power adapter: 24V, 0.5A (12 Watts) - Power mode: Passive Power over Ethernet (4.5+ threads, 7.8 return) - Operating temperature: -30 ° C + 80 ° C -Humanity of operation: 5 to 95% with condensation - Operating system: AirOS V |
| Technical brochure | http://dl.ubnt.com/loco_m2_datasheet.pdf |
| Installation guide | https://www.ubnt.com/downloads/guides/NanoStation_M/NanoStation_M_Loco_M_QSG.pdf |
| Review date | 10-12-2015 by DLS |
10 other products in the same category:
ADAPTADOR NATEC MULTIPUERTO USB-C A USB...
€12.50
HPE Aruba IOn 1430 8G Sw
€48.32
KEENETIC ORBITER PRO (KN-2810) PERP
€77.35
A21 AC2100 DUAL BAND WI-FI PERP
€41.57
24-PORT GIGABIT SWITCH(RACK CPNT
€86.53
24-port Giga Poe Smart 4x10g Sfp+
€552.90
D-Link DGS-1210-28MP/E Switch 24xGb PoE+...
€494.88
D-Link GO-SW-16G Switch 16xGB
€54.65
Switch Gen2 16 Puertos Poe
€190.29
2.5 Gigabit PCI Express Network
€22.73
Reviews (0)